Configurator: parameter scale2 - Versionsgeschichte

Fbernardo am 7. Dezember 2020 um 14:11 Uhr

2020-12-07T14:11:04Z

Fbernardo am 7. Dezember 2020 um 14:08 Uhr

2020-12-07T14:08:51Z

Fbernardo am 7. Dezember 2020 um 14:07 Uhr

2020-12-07T14:07:24Z

Fbernardo: /* Data-Bits */

2020-12-04T09:17:19Z

Data-Bits

Fbernardo: /* data-Bits */

2020-12-04T09:17:08Z

data-Bits

Fbernardo am 4. Dezember 2020 um 08:24 Uhr

2020-12-04T08:24:17Z

Fbernardo: Die Seite wurde neu angelegt: „ In this section you can change the settings for the connected scale. Under Parameter Scale2 you will find all configuration possibilities for the 2nd scale.<…“

2020-12-04T08:23:57Z

Die Seite wurde neu angelegt: „ In this section you can change the settings for the connected scale. Under Parameter Scale2 you will find all configuration possibilities for the 2nd scale.<…“

Neue Seite

In this section you can change the settings for the connected scale.

Under Parameter Scale2 you will find all configuration possibilities for the 2nd scale. If you want to use more than one scale at a packing station, because, for example, not only packages but also pallets are packed at this packing station. Then you have the possibility to define another scale under [[Configurator:_parameter_scale1|parameter scale1]].

The selection of the scale (1 or 2) for weighing is done via the set parameter in the configurator of the respective carrier.

Please note that due to the high variation of scale manufacturers and scale models, we can only support the scales purchased from us. A list of the packaged scales distributed by us can be found on our [https://heidler-strichcode.de/accesories/?lang=en Homepage].

[[Datei:Configurator scale2.PNG|right|700x900px|Konfigurator waage2.PNG]]

= scale type =

Make the selection of the scale type of the scale connected via the serial interface. For scales with a TCP/IP connection, please follow the configuration steps of the also installed documentation of the ScaleService.

= scale on/off =

With this function you can activate (On) or deactivate (Off) the scale. To configure and use the scale, it must be active (On). If the scale is deactivated, the weight input in the processing mask is set directly to "Manual" for manual processing unless otherwise specified.

= scale port =

Select the serial communication port (COM port) to which the scale is connected. Note that when using USB/RS232 adapters, communication may be unstable and the COM port may change, e.g. after a system restart.

= transfer rate (Baudrate) =

Select the transfer rate (Baudrate) used by the scale. If necessary, check the setting on the scale e.g. using a weighing terminal.

= Parity-Bit =

Select whether a parity bit is used during communication to check transmission. If necessary, check the setting on the scale e.g. using a weighing terminal.

= data-Bits =

Select how many data bits are used in the transfer. If necessary, check the setting on the scale e.g. using a weighing terminal.

= Stop-Bits =

Select how many stop bits are used in the transfer. If necessary, check the setting on the scale e.g. using a weighing terminal.

= start/end frame =

With certain types of scales an optional request frame can be activated. If the frame is activated, the request telegram is enclosed with a special frame.

With the scale type '''Bizerba''' the frame '''<SOH>'''[Request]'''<ETB>''' is used for example.

= scale parameter test =

Before the scale test, save the set parameters using the buttons '''Next''' and '''Back'''.

With the button '''scale parameter test''' you can then check the configuration and the scale functionality.

Please note that some types of scales do not send a response to the requesting system if the weight is not weighable (e.g. if it is too low).

@@ Zeile 8: / Zeile 8: @@
 Please note that due to the high variation of scale manufacturers and scale models, we can only support the scales purchased from us.<br/> A list of the packaged scales distributed by us can be found on our [https://heidler-strichcode.de/accesories/?lang=en Homepage].
-[[Datei:Configurator scale2.PNG|right|700x900px|Configurator scale2.PNG]]
+[[File:Configurator scale2.PNG|right|700x900px|Configurator scale2.PNG]]
 = scale type =

← Nächstältere Version		Version vom 7. Dezember 2020, 14:08 Uhr
Zeile 1:		Zeile 1:
−	[[de:Konfigurator:_Parameter ~~Waage1~~]]	+	[[de:Konfigurator:_Parameter Waage2]]
	In this section you can change the settings for the connected scale.		In this section you can change the settings for the connected scale.

← Nächstältere Version		Version vom 7. Dezember 2020, 14:07 Uhr
Zeile 1:		Zeile 1:
−		+	[[de:Konfigurator:_Parameter Waage1]]
	In this section you can change the settings for the connected scale.		In this section you can change the settings for the connected scale.

@@ Zeile 30: / Zeile 30: @@
 Select whether a parity bit is used during communication to check transmission.<br/> If necessary, check the setting on the scale e.g. using a weighing terminal.
-= Data-Bits =
+= data-Bits =
 Select how many data bits are used in the transfer.<br/> If necessary, check the setting on the scale e.g. using a weighing terminal.

@@ Zeile 30: / Zeile 30: @@
 Select whether a parity bit is used during communication to check transmission.<br/> If necessary, check the setting on the scale e.g. using a weighing terminal.
-= data-Bits =
+= Data-Bits =
 Select how many data bits are used in the transfer.<br/> If necessary, check the setting on the scale e.g. using a weighing terminal.